1. Clutch pedal
   Accelerator pedal
2. Brake pedal
   Pedal to the metal!

That's right, in a car with a manual transmission, you will find an extra pedal in the cabin at the driver's feet. In a left-hand drive car, this pedal is found on the right of the brake pedal (middle) and accelerator pedal (far left). The clutch pedal is engaged when the driver wants to change gears.

1. Driving too fast
   Using the incorrect gears
2. Driving too slowly
   None of the above

Although an automatic transmission will change the gears for you, when towing a large load, many drivers prefer to override the system and pick the gear they think is best by themselves. If they know what they are doing, then it's all fine, but inexperienced drivers often pick the wrong gear.

1. Front engine, front-wheel drive
   Front engine, rear-wheel drive
2. Rear engine, front-wheel drive
   Rear engine, rear-wheel drive

Over the years, cars have had many different engine positions and drivetrain configurations. Think of the muscle cars of the 1960s - people loved how they had massive engines located in the front of the car but that all that power was transferred to the rear wheels, allowing drivers to light up the tires and lay down some rubber. Most modern cars, however, are front engined, front-wheel drive cars.

1. 1
   22
2. 15
   6

Notice that in this question, we did say MOST modern cars. Why? Well, it can vary. Although most modern automatic transmission cars have six gears available, some are different. Take the Chrysler 200, which is a 9-speed. In the past, many automatic transmission cars had a four-speed transmission.

1. Selects the best gear to make the car go fast
   Transfers the power created by the engine to the wheels
2. Makes sure the car runs economically
   None of the above

Without a transmission system, be it manual or automatic, your car would simply not move, no matter how much power it generates. The transmission system on a car is tasked with turning the power created by the engine into a forward (or reverse) motion in the wheels.

1. True
2. False

Why? Well, it just seems that Americans love their automatic transmission vehicles over their stick shift counterparts. The fact that pickups are very popular in the States (and most of these have automatic transmissions) must surely boost the figure somewhat as well.

1. Self-shifting transmission
   Auto-gearo
2. Gearing selector auto
   None of the above

We know it mainly as the automatic transmission but it also has many other names. Perhaps the second most popular is self-shifting transmission, but other names include auto-shifting transmission and 6-speed automatic (substitute the numeral for the number of gears the vehicle has).

1. Hydraulic automatic transmission
   Gas automatic transmission
2. Steam automatic transmission
   None of the above

Most automatic transmissions found on vehicles today are of a hydraulic nature. This means gear changes are achieved by using hydraulics to unlock and lock a system of gears, commonly known as planetary gears.

1. Automatic transmission pump
   Fuel pump
2. Oil pump
   None of the above

Often considered to be the heart of the transmission system, the automatic transmission pump moves hydraulic fluid through the gearing system to ensure it operates efficiently.

1. True
2. False

Unlike in America where the figure is the same but in the opposite direction, Europeans seem to love a manual transmission car over an automatic transmission one. Also, pickups are not as huge in Europe as in the States, so there is a large portion of automatic transmission vehicles that just aren't sold over the pond.

1. Easy shifting
   "You choose" shifting
2. Stick shift
   None of the above

You won't find many vehicle aficionados in the United States saying they bought a manual transmission car. To Americans, it simply is called a stick shift.

1. Planetary gear
   Carrier assembly
2. Shift lever
   Slave cylinder

A crucial part of the transmission, the planetary gear set helps to make all the various ratios that the gears in the transmission can produce. It consists of the sun, planetary and ring gears.

1. 1981
   1921
2. 1973
   1945

Although motor vehicles as we know them had been around since 1885, those early cars and models up to the 1920s were all manual gearbox vehicles. The first automatic transmission was invented in 1921.

1. Alfred Horner Munro
   Louis Chevrolet
2. Henry Ford
   Ransom E. Olds

We have Alfred Horner Munro to thank for the invention of the first automatic gearbox. A resident of Regina in the Saskatchewan province of Canada, Munro came up with his design in 1921 and by 1923 had patented it.

1. Louis-Rene Panhard and Emile Levassor
   Karl Benz
2. William C. Durant
   Adam Opel

The first modern manual gearbox was invented by two Frenchmen, Louis-Rene Panhard and Emile Levassor. Their first unit was a three-speed manual transmission and many of their design ideas are still used today.

1. 1944
   1925
2. 1894
   1778

Louis-Rene Panhard and Emile Levassor introduced their first manual transmission in 1894. It was a simple three-speed gearbox. It had no clutch and gears would carefully be selected when the motor was running at the correct speed for that gear.

1. Sliders
   Unsynchronized transmission
2. Mesh-o-Matic
   None of the above

Early manual transmission systems required excellent timing and a knowledge of how fast the engine was rotating to select the correct gear. Because no clutch was involved to disengage the engine, these types of manual transmissions were referred to as unsynchronized transmissions.

1. True
2. False

True, automatic transmissions certainly have more than one clutch. In fact, they can have several. These clutches are tasked with both engaging and disengaging a specific set of planetary gears assigned to them and related to the speed the vehicle is going and the correct gear it needs to be in based on that.

1. Synchronized transmission
   Slekta (TM)
2. Double clutch transmission
   None of the above

It's pretty complex and impossible to explain in a few sentences, but in essence, a clutch allows the right gear to be selected without having to worry about adjusting the speed of the engine to allow the gears to mesh. This is called a synchronized transmission.

1. 1955 Volvo
   1940 Oldsmobile
2. 1960 Aston Martin DB5
   1955 Chevrolet Corvette

The idea for the first hydraulic-based automatic transmissions was sold to General Motors by two Brazilian engineers, José Braz Araripe and Fernando Lehly Lemos. GM then introduced this new radical design for the first time in Oldsmobile models in 1940.

1. The auto-transo system
   Hydra-Matic transmission
2. Self-shifter transmission
   General Motors Shifto

General Motors decided that a catchy name would be the best way to market its new automatic transmission system. The company called it the "Hydra-Matic" and you can even hear it mentioned in the classic song "Greased Lightning" from the hit movie, "Grease".

1. It catches fire.
   It wears out over time.
2. It falls off.
   It doesn't work in cold conditions.

Because a clutch is employed so often and drivers will sometimes "ride" it, particularly while standing still at a traffic light instead of engaging the brake and putting the car in neutral, it will wear out over time. A worn clutch will start to slip and not engage as it should, causing higher revving as you gear up.

1. Clutch cable
   Torque converter
2. Output shaft
   Axle shaft

Found in cars with automatic transmissions, a torque converter fulfills the same role as a clutch in a manual transmission car. Essentially, it keeps the engine turning over when the vehicle comes to a halt.

1. Prop shaft
   Collar
2. Shift fork
   Pinion

The collar is a vital part in a manual transmission. It will shift left or right along the shaft to select and engage the gear as the driver chooses them using the gear shift.

1. The air conditioning system
   The cooling system of the engine
2. By the wind
   None of the above

With so many moving parts and spinning gears, all moving and interlinking, it is natural that an automatic transmission system will overheat. Luckily, it is kept from overheating by using an existing cooling system found on the vehicle already: the engine cooling system.

1. Elastic bands
   Timing bands
2. Transmission ropes
   None of the above

Made from steel, timing bands are straps that are found in the transmission on drums within it. These drums will rotate when the band is not pressed against it to grip it. Stopping their rotating means components within the transmission interact in different ways, depending on what the driver is doing in terms of gear selection.

1. Park
   1st
2. 2nd
   3rd

When stopping a car with an automatic transmission, the vehicle should be placed in the park gear. This locks the transmission's output shaft and means the vehicle cannot move forward or backward.

1. 1st gear
   3rd gear
2. 2nd gear
   4th gear

In an automatic transmission, a ratio of 1-1 is achieved when the vehicle is shifted into third gear. It means the output shaft as well as the input shaft both turn at the same time and together.

1. Clutch lining
   Differential gear
2. Sensors
   Transmission yoke

In modern automatic transmission systems, sensors on the engine and within the transmission itself track speed, the position of the throttle, the speed of the engine and other factors to control shift points.

1. True
2. False

A finger shift allows a driver to change gear with the mere movement of their finger. An example of this is on buses in Japan where the system has been used on heavy-duty buses since 1983.

1. Continuously variable transmission
   Car vehicle transmission
2. Common vehicle transmission
   None of the above

In a continuously variable transmission, the gearbox is able to select from any number of gear ratios. In fact, the options are practically infinite. This allows it to select the most effective gear for any situation.

1. Spider gears
   Valve body
2. Transmission yoke
   None of the above

In automatic transmissions, the valve body is vitally important. It helps direct hydraulic fluid to valves in the transmission that in turn engage the appropriate band servo or clutch pack needed at that time.

1. Ring gear
   Throttle gear
2. Finger gear
   Clutch gear

The ring gear is the large outer gear in the planetary gear system in the transmission. It is tasked with moving the torque from the secondary shaft through to the differential.

1. Ring gear
   Sun gear
2. Differential gear
   None of the above

The sun gear is the central gear in the planetary gear system in the transmission. It is tasked with spinning the other gears in the planetary gear system.

1. It tells the driver which is the best gear to be in.
   It tells the driver when to brake.
2. It tells the driver when to shift.
   None of the above

In a manual transmission vehicle, a tachometer is of massive importance, especially if you intend to rev the motor to the redline often. The tachometer is just a simple way for the driver to see when he should shift gears.